The Stroke style tab has options to change the style of an object's path. This includes the stroke width, Join style, Cap style, Dash Pattern, and Markers.
Stroke width can be changed by the Width entry box. The units are specified by the drop-down menu on the right.
New in v0.47:
Stroke Gestures. Stroke Gestures is the name give to changing the Stroke width by dragging the mouse from the Stroke width indicator into the Inkscape window. The principle is that as you drag the mouse, the line width will change proportionally to the distance from a 45° line from the indicator. The farther away you are, the more subtle the changes can be. The maximum width increase is a factor of 4 and the minimum width is zero. See Color Gestures for more details.
The Join style is how two lines meeting at a corner should be joined together. The options are:
The different Join styles are shown in the figure following.
When the Miter option is selected, the length of the projection can become quite long if the two lines intersect at a small angle. In this case, it may be preferable to use the Bevel style. The Miter limit controls the point at which a Miter join automatically is converted to a Bevel join. If the distance from the inner intersection point to the tip of the triangle ("m" in the following figure) measured in stroke widths is more than the Miter limit, the join will be drawn in the Bevel style.
The visual bounding box is determined by assuming that the Join style is Round.
The Cap style determines how the end of a line is drawn. The options are:
The different Cap styles are shown in the figure below.
The visual bounding box is determined by assuming the Cap style is Round.
A wide selection of Dash patterns are available from the drop-down Dash menu. The patterns scale with the stroke width.
Each Dash takes on the Cap style as shown in the figure below.
The entry box next to the Dash menu is for the Dash offset. The offset shifts the Dash pattern along the path. The units are in stroke width.
Markers are objects like arrow heads placed along a path. Different Markers can be specified for the start, middle, and end of a path. Middle Markers are placed at the location of every non-end node.
A custom Marker can be created by selecting the object or objects that you wish to use as a Marker and then using the → command. The selected objects will disappear and a new entry will appear in the Marker pull-down menus of the Fill and Stroke dialog. The Marker is created assuming a horizontal orientation for the path. The point of attachment to a node is the center of the bounding box for the Marker. Warning: While the marker will display fine in Inkscape, only a fourth of it will be displayed in most other SVG renderers. Adding the attribute style="overflow:visible" to the Marker definition will fix the problem (Bug). Note, that custom Markers can be added to Inkscape; see the section called “Custom Markers” in Chapter 23, Customization.
Two problems exist with Markers. The first is that Markers do not take the color of the stroke. This can be worked around by using the Color Markers to Match Stroke extension, by editing the SVG file with the XML Editor, or adding a custom, pre-colored Marker. An alternative solution is to convert the path with the Markers to a path ( → (Shift+Ctrl+C)). This creates a Group with the Markers converted to separate objects, which can be colored independently.
The second problem is that Markers scale with line width. The line width had to be reduced in the above figure for the scissors examples, to give the scissors a reasonable size. Again, one could edit the SVG file to adjust the Marker size.
To place middle Markers evenly along a path you need to have evenly spaced nodes. For straight horizontal and vertical lines, nodes can be distributed evenly using the Align and Distribute dialog. To add just one node halfway between two existing nodes click on the Insert icon in the Node Tool-Tool Controls. To add one node anywhere on an existing path, double click on the path where you want the node (or single click while holding down the Ctrl+Alt keys). To add multiple nodes evenly spaced between existing nodes, use the Add Nodes extension.
Another thing to note is that Markers are included in the Visual bounding box calculation.
A complex Stroke can be created by overlaying two or more paths with different Stroke attributes. The easiest way to make exact copies of a path is to use the → (Ctrl+D) command.
If one uses Clones of a path ( → → (Alt+D)), then one can adjust the original path at a later time and all the Clones will change too. This requires unsetting the Stroke attributes of the original path (use the XML editor to unset the Stroke width). Since the original path's attributes are unset, it will not be visible and cannot be used as part of the visible Stroke.
|© 2005-2010 Tavmjong Bah.||Get the Book or PDF.|