Major changes for v0.47.
To help precisely place objects on the canvas, an object can be made to snap to a target. The target can be a points on another object, the page boundary, a Grid line, or a Guide Line. Snapping takes place when some defined point on an object, a snapping point, is near a target. Snapping can be divide into two parts: defining snapping points and setting targets. As of v0.47 this is done with the Snap Bar (in v0.46 the Snap tab of the Document Properties dialog is used). Snapping was introduced in the tutorials at the beginning of the book.
Snapping can be set to always happen or only happen when a snapping point is within a set distance (the Snap Distance) from a target. Setting Snap Distance is made under the Snap tab of the Document Properties dialog.
In v0.47 when a snapping point is snapped to a target, a small cross will flash at the snapping site. Next to this indicator, a message indicates what snapping point and snapping target were used. The indicator can be disabled in the Snapping section of the Inkscape Preferences dialog by unchecking the Enable snap indicator option.
A few other options can be found under the Snapping section of the Inkscape Preferences dialog:
Delay (in ms): Sets the delay between the time the cursor stops moving and snapping is attempted. Useful if there are many snapping targets (e.g., with a Grid).
Only snap the node closest to pointer: If this option is enabled, only one node is used as a snapping point on a target. This node will be highlighted as an object is dragged. Useful if an object has many snapping points. Note: if an object has too many nodes, and this option is disabled, a “convex hull” is used for snapping.
Weight factor: If multiple snapping possibilities exist, the value of this parameter determines if the smallest distance between a snap point and snap target is favored (0.0) or if a snap using the closest snap point to the cursor is preferred (1.0).
The Snap Bar includes a variety of clickable icons that toggle various snap points and targets on and off. It is divided into a number of sections. (The Snap tab has similar sections in v0.46.) The first section has one icon ( ) for globally toggling on or off snapping (this includes snapping to Guide Lines and Grids). The second section concerns snapping to and from points defined by objects' bounding boxes. The third section covers options for snapping to and from nodes and handles. The last section has icons for toggling on and off snapping to the page boundary, Guide Lines, and Grids. Note that snapping of bounding boxes is independent of snapping of nodes (i.e., a node cannot be directly snapped to a point on a bounding box and vice versa). Both bounding boxes and nodes, however, can be snapped to the page boundary, Guide Lines and Grids.
The section for snapping bounding box items includes the icons for enabling and disabling:
Most types of nodes and handles can be snap points and/or targets. These include path nodes, regular Shape nodes and handles, Rectangle round-corner handles, and Rotation center handles. The options in the Snap Bar section for nodes and handles includes icons for enabling and disabling:
Guide Lines are individual lines that can be arbitrarily placed. They are defined by an x-y anchor (origin point) through which the line passes and an angle. The anchor is shown as a small circle on the line in v0.47.
Guide Lines can be hidden or unhidden by using → (|). To be active, a Guide Line must be visible. Snapping to Guide Lines can be enabled or disabled by clicking on the icon in the Snap Bar.
The color of Guide Lines can be changed under the Guides tab in the Document Properties dialog. Snapping of Guide Lines to other objects can be enabled or disabled also under this tab.
To create a Guide Line, Left Mouse Drag from the left Ruler onto the canvas for a vertical Guide Line or from the top Ruler for a horizontal Guide Line. An angled Guide Line can be created by dragging from the end of a Ruler. By default, the angle is set to 45° if a rectangular Grid is displayed or parallel to the angled lines if an axonometric Grid is displayed.
Guide Lines can be translated and rotated (in v0.47) using the mouse:
Left Mouse Drag: Translate Guide Line. Both the Guide Line and anchor are moved. If the dragged off the page, the Guide Line is deleted.
Shift+Left Mouse Drag: Rotate Guide Line. Rotation is around the anchor. You must be a small distance away from the anchor for rotation to be enabled.
New in v0.47.
Ctrl+Left Mouse Drag: Move the anchor, constrained to the Guide Line.
New in v0.47.
Ctrl+Shift+Left Mouse Drag: Rotate Guide Line with constraint. Angle snaps to multiples of the Rotation snap angle, (15 degrees, by default).
New in v0.47.
Del: While over a Guide Line, delete the Guide Line.
Guide Lines can be precisely placed by using the Guide Line dialog, called up by double clicking on a Guide Line. A check box toggles between absolute and relative placement.
Guide Lines can be created from objects using the → (Shift+G) command. The keyboard shortcut works with the Select Tool, shape tools, Bezier Tool, and Pencil Tool. Different objects are converted in different ways. In each case, the selected objects are deleted unless the Keep objects after conversion to guides entry is checked in the Tools section of the Inkscape Preferences dialog.
Changed in v0.47:
A Grid is composed of two or three sets of evenly spaced parallel lines. A Rectangular Grid consists of horizontal and vertical lines, much like a sheet of ordinary graph paper. An Axonometric Grid consists of three sets of parallel lines, typically one vertical and two at 30° angles from the horizontal. It is often used to draw three-dimensional objects.
Grids can be created and edited on the Grids tab of the Document Properties dialog. To create a Grid, select the type (Rectangular or Axonometric) from the drop-down menu at the top of the dialog and then click on the New button. The parameters for the new Grid will then be editable under a tab in the bottom of the dialog. It is possible to have more than one Grid defined (and in use). Each Grid will have a tab entry.
Each Grid can individually be Enabled and made Visible by the check boxes on the Defined Grid tabs. If a Grid is not enabled, it will not be visible. However a Grid can be enabled and not visible. All Grids can be enabled or disabled by clicking on the in the Snap Bar or by using the global command → (#). This setting overrides the settings on the individual Grid tabs. Note: There is no visual indication if this overall setting is on or off if the visibility of the individual Grids are all set off. Note also that, depending on the zoom scale, not all Grid lines are shown. “Missing” lines will not be snapped to if the Snap to visible grid lines only box is checked under the Grids tab (option new in v0.47).
For both types of Grids, the Grid unit can be selected from a drop-down menu and the Grid origin can also be specified. For Rectangular Grids, the x and y spacing can be set independently. For Axonometric Grids the x and z spacings are derived from the y spacing and the angle settings. In both cases the color of the lines can be set by clicking on the color box and making changes in the dialog that pops up.
The default Grid parameters can be modified in the Grids section of the Inkscape Preferences dialog.
Different “views” of the same drawing share the same Grids but the Grids can be enabled or made visible independently for each view.
|© 2005-2010 Tavmjong Bah.||Get the Book or PDF.|